Visonic POWERMASTER-10 Podręcznik Użytkownika Strona 83
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
APPENDIX D. Event Codes
D-304762 PowerMaster-10/30 G2 Installer's Guide
83
Code Definition
Code Definition
FT
Fire Detector Clean
XT
Sensor Battery Trouble
FX
Fire test
YA
Bell Fault
GA
Gas alarm
YH
Bell Restored
GJ
Gas trouble restore
YI
Overcurrent Trouble
GR
Gas alarm restore
YM
System battery disconnect
GT
Gas trouble
YR
System Battery Restore
GX
Gas test
YT
System Battery
Trouble / Disconnection
HA
Holdup Alarm (duress)
YX
Service Required
JT
Time Changed
YZ
Service Com
pleted
KA
Heat alarm
ZA
Freeze alarm
KH
Heat alarm restore
ZH
Freeze alarm restore
KJ
Heat trouble restore
ZJ
Freeze trouble restore
KT
Heat trouble
ZR
Freeze restore
LB
Local Program
ZT
Freeze
trouble
LR
Phone Line Restore
D3. Understanding the Scancom Reporting Protocol Data Format
The SCANCOM data format consists of
13 decimal digits divided into 4 groups,
from left to right, as shown on the right.
Each channel is associated with a
specific event as follows:
1
st
"C": Fire
2
nd
"C": Personal attack
3
rd
"C": Intruder
4
th
"C": Open/close
5
th
"C": Alarm cancel
6
th
"C": Emergency
7
th
"C": Second alarm
8
th
"C": Trouble messages
Account
Code
aaaa
Channels
1 - 4
cccc
Channels
5 - 8
cccc
S
System Status:
no trouble, test,
low battery
- - - - - - - -
The digit in this position
conveys the status of
channel 1
The digit in this position
conveys the status of
channel 8
Scancom Data Format
D4. SIA over IP - Offset for Device User
Type Number Range
In Hex
Example Remarks
System reports 00 System tamper would report as 000
Normal Zones/Detectors 0-499 Zone 5 would report as 005
Keyfobs / Users /Tags 501-699 Keyfob/User number 101 would report
601
Keypads/ASU 701-799 Keypad number 8 would report 708
Sirens 801-825 Siren number 9 would report 809
Repeaters 831-850 Repeater number 4 would report 834
Expanders/Bus devices/PGM 851-875 Device number 2 would report 852
Troubles for:
GSM
Plink
Guard
876
878
879
CSM module network fail 876
901- 999 For future use
- PowerMaster-10/30 G2 1
- Version 17 1
- 1. INTRODUCTION 3
- Figure 3.2 –Phone Wiring 9
- 3.4 GSM Module Installation 10
- 3.5 PGM-5 Installation 11
- Figure 3.6a – Cable Wiring 12
- UL listed 13
- PGM: not to be enabled in UL 13
- Figure 3.7a - Power Cable 14
- Connection 14
- Figure 3.9 - Final Closure 16
- Figure 4.3a – Phone Wiring 18
- 4.6 GSM Module Installation 20
- 4.8 PGM-5 Installation 21
- Figure 4.9a –Expander Module 22
- Figure 4.9b – Zone 23
- and Siren Wiring 23
- 4.11 Battery Insertion 25
- Figure 4.13 26
- 5. PROGRAMMING 27
- [1] in Step 1 above) 28
- 5.2.2 Selecting options 28
- – Exiting the Installer Mode 29
- – Setting Installer Codes 29
- 5.4 Zones / Devices 30
- Part B - Configuration 31
- - Configuring New Devices 32
- 5.4.3 Deleting a Device 34
- 5.4.5 Replacing a Device 34
- – Replacing a Device 35
- – Changing Defaults 35
- 5.5 Control Panel 36
- 01:ENTRY DELAY1 37
- 02:ENTRY DELAY2 37
- VOICE REPORT 38
- SMS REPORT 38
- 09:ARMING KEY 39
- 21:SWINGER STOP 39
- 22:CROSS ZONING 39
- 38:CANCEL ALARM 41
- 39:ALARM RESET 41
- 40:ABORT FIRE T 41
- 43:PANEL SIREN 41
- 44:SIREN TIME 41
- 5.6 Communication 44
- PowerMaster String Editor 48
- Event Reporting Chart 51
- IMAGE FORWARD 52
- 1st e-mail 52
- 2nd e-mail 52
- 5.6.8 Broadband 54
- 5.7 PGM Output 55
- 5.8 Custom Names 56
- 5.8.2 Record Speech 57
- 5.8.3 Voice Box Mode 57
- 5.9.4 Testing the SIM Number 60
- 5.10 User Settings 61
- 5.11 Factory Default 61
- 5.12 Serial Number 61
- 5.13 Start UL/DL 62
- 5.14 Partitioning 62
- 5.15 Operation Mode 62
- 5.15.2 Select setting 63
- 5.15.3 BS8243 Setup 63
- 5.15.4 DD243 Setup 64
- 5.15.5 CP01 Setup 66
- 5.15.6 OTHERS Setup 67
- 6. PERIODIC TEST 68
- 7. MAINTENANCE 70
- 7.4 Fuse Replacement 72
- 7.6 Annual System Check 72
- 8. READING THE EVENT LOG 73
- APPENDIX A. Specifications 74
- A2. Wireless 75
- A3. Electrical 75
- A4. Communication 76
- A5. Physical Properties 77
- B2. Common Areas 78
- Assignments 79
- C2. Keyfob Transmitter List 80
- APPENDIX D. Event Codes 82
- Type Number Range 83
- APPENDIX E. Sabbath Mode 84
- F1. Getting Started 85
- F2. Specifications 85
- F3. Installation 86
- Hardware Installation 87
- Control Panel Configuration 89
- APPENDIX G. Glossary 90
- Compliance with 92
- Standards 92
- WARRANTY 93
- Initiating Alarms 95
- Preparing to Arm 95
- Zone Bypass Scheme 96
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Visonic POWERMASTER-10
(27 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji