Visonic POWERMASTER-10 - INSTALLER GUIDE Dokumentacja Strona 49
- Strona / 82
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
5. PROGRAMMING
48 D-303222 PowerMaster-10/30 G2 Installer's Guide
Option
Configuration Instructions
Entering Hexadecimal Digits
Digit
0…..9
A
B
C
D
E
F
Keying
0…..9
[#]
[0]
[#]
[1]
[#]
[2]
[#]
[3]
[#]
[4]
[#]
[5]
16:PSTN/GSM RCV1
17:PSTN/GSM RCV2
Master Installer only
The PowerMaster can be programmed to report the event messages defined in the Report
Events option (option 01) to two Alarm Format Receivers via PSTN telephone line and/or
GSM analog voice channel (if equipped with GSM module), using standard PSTN alarm
formats (i.e. SIA and/or Contact-ID approved by UL, and Scancom not for UL). The reporting
format is defined in the "PSTN Report Format" option (option 41).
Enter the two respective telephone numbers (including area code – maximum 16 digits) of
the Alarm Format Receiver 1 located at the 1
st
Monitoring Station (16: PSTN/GSM RCV1)
and alarm format Receiver 2 located at the 2
nd
Monitoring Station (17: PSTN/GSM RCV2).
Note: If any of the phone numbers programmed herein contain an area code identical to the
area code of the PSTN telephone line to which the system is connected, you should refer to
the "AREA CODE" option in section 5.6.2.and act as instructed there.
Digit
Keying
Digit Significance
A
[#]
[0]
The dialer waits 10 seconds or waits for dial tone, whichever comes first
and then dials. Applicable only at the 1
st
digit.
D
[#]
[3]
The dialer waits 5 seconds for dial tone and goes on hook if none is
received. Applicable only at the 1
st
digit.
E
[#]
[4]
The dialer waits 5 seconds. Applicable only in the middle of the number.
To move the cursor and clear digits, use the "String Editor's" keys as described in the
table at the end of section 5.6.3.
21:IP RCVR 1
22:IP RCVR 2
Master Installer only
If equipped with GSM or Broadband/PowerLink modules, the PowerMaster can be programmed
to report the event messages defined in Report Events option (option 01) to two IP Receivers,
Visonic PowerManage model. IP reporting can be performed via GPRS (IP) channel using SIA
IP format or via Broadband IP channel using SIA IP or Visonic PowerNet format.
Enter the two IP addresses (000.000.000.000) of the IP Receiver 1 located at the 1
st
Monitoring
Station (21:IP RCVR 1) and IP Receiver 2 located at the 2
nd
Monitoring Station (22:IP RCVR 2).
26:SMS RCVR 1
27:SMS RCVR 2
Master Installer only
If equipped with GSM module, the PowerMaster can be programmed to report the event
messages defined in Report Events option (option 01) to two SMS Receivers via the GSM
SMS channel using a special SMS text format. For further details concerning the SMS text
format please contact Visonic.
Enter the two telephone numbers (including area code – maximum 16 digits).of the SMS
Receiver 1 located at the 1
st
Monitoring Station (26:SMS RCVR 1) and SMS Receiver 2
located at the 2
nd
Monitoring Station (27:SMS RCVR 2).
Notes:
1. To enter the international prefix (
) at the 1
st
digit – key-in [#]
[1].
2. SMS is not sent to UL/ULC listed Monitoring Station receivers. This is a supplementary
feature of the PowerMaster-10/30 G2.
41:PSTN FORMAT
The PowerMaster can be programmed to report the event messages defined in Report
Events option (option 01) to two Alarm Format Receivers (see options 16 & 17) via PSTN
telephone line and/or GSM analog voice channel (if equipped with GSM module) using
standard PSTN alarm formats (i.e. SIA, Contact-ID and Scancom).
Select which of the reporting formats the system will use to report the events to the two Alarm
Format Receivers PSTN/GSM RCVR 1 and PSTN/GSM RCVR 2. The Event Codes used for
the reporting in each of the available formats are specified in APPENDIX D. Event Codes.
Make sure that the receivers used by the Monitoring Stations are of the compatible models
listed below and that the receiver used can receive the format you select.
Compatible Alarm Format Receivers:
UL/ULC listed receivers: SG-System I, SG-System III, SG-System IV.
Master Installer only
Options: SIA (default); Scancom; SIA text and contact ID.
- INSTALLER GUIDE 1
- PowerMaster-10/30 G2 2
- Version 16 2
- Installer's Guide 2
- 1. INTRODUCTION 4
- Figure 3.2 –Phone Wiring 10
- 3.4 GSM Module Installation 11
- 3.5 PGM-5 Installation 12
- Figure 3.6a – Cable Wiring 13
- Figure 3.7a - Power Cable 15
- Connection 15
- Figure 3.9 - Final Closure 17
- Figure 4.3a – Phone Wiring 19
- Figure 4.6 21
- Figure 4.9a –Expander Module 23
- Figure 4.9b – Zone 24
- and Siren Wiring 24
- 4.11 Battery Insertion 26
- Figure 4.13 27
- 5. PROGRAMMING 28
- [1] in Step 1 above) 29
- 5.2.2 Selecting options 29
- or 30
- 5.4 Zones / Devices 31
- Part B - Configuration 32
- - Configuring New Devices 33
- 5.4.3 Deleting a Device 35
- 5.4.5 Replacing a Device 35
- 5.5 Control Panel 37
- VOICE REPORT 39
- SMS REPORT 39
- 5.6 Communication 44
- String Editor Functionality 47
- Voice <- -> C.S 51
- Ringback time 51
- Ambient level 51
- Mast. UL/DL code 53
- Inst. UL/DL code 53
- 5.7 PGM Output 54
- Zone B Z:_ _ 55
- Zone C Z:_ _ 55
- 5.8.2 Record Speech 56
- 5.9.3 Testing the GSM module 58
- 5.10 User Settings 59
- 5.11 Factory Default 59
- 5.12 Serial Number 59
- 5.13 Start UL/DL 60
- 5.14 Partitioning 60
- 5.15 Operation Mode 60
- 5.15.3 BS8243 Setup 61
- 5.15.4 DD243 Setup 62
- 6. PERIODIC TEST 63
- <location> 65
- 7. MAINTENANCE 66
- 7.4 Fuse Replacement 67
- 8. READING THE EVENT LOG 68
- APPENDIX A. Specifications 69
- A2. Wireless 70
- A3. Electrical 70
- A4. Communication 71
- A5. Physical Properties 71
- (optional) 72
- Assignments 73
- APPENDIX D. Event Codes 75
- D2. SIA Event Codes 76
- APPENDIX E. Sabbath Mode 77
- APPENDIX F. Glossary 78
- Compliance with 80
- Standards 80
- WARRANTY 81
- PowerMaster-30 G2 82
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Visonic POWERMASTER-10 - INSTALLER GUIDE
(9 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji