Visonic POWERMASTER-10 Podręcznik Użytkownika Pobierz pdf (Strona 72)

D-304271 PowerMaster-10/30 G2 Addendum 3

BS8243 Setup

13:OPERATION MOD

⋅ ⋅ ⋅

02:BS8243 SETUP

Enter the "02:BS8243 SETUP " menu, and press to configure BS8243 compliance standard settings.

Option Configuration Instructions

01:DISARM OPTION

Define when it is possible to disarm the system:

entry/BS devs (default) – By keypad after the entry delay has expired and if an alarm

occurred in the system. By keyfob or keyprox at all times.

Entry/all devs - During entry delay, when the system is armed AWAY, by all devices. When

not in entry delay by keyfob or keyprox only.

entry/DD devs - During entry delay, when the system is armed AWAY, by using the keyfob or

keyprox. Keypads cannot disarm at all.

anytime/all dev – At any time and by all devices.

02:ENTRY ALARM

Define whether the system will report a confirmed alarm during an entry delay (see CONFIRM

ALARM below).

BS8243 (default) – An alarm initiated by another detector during the entry delay is regarded as a

confirmed alarm. An additional 30 seconds delay is added to the entry delay for reporting the event

(does not affect the Abort Time, see section 3.5.4).

BS8243 no cnfrm - The panel will not send any confirmed alarm once a delay zone has been

activated, until the control panel is disarmed.

DD243 - An alarm initiated by another detector during the entry delay is not regarded as a

confirmed alarm.

EN standard - The control panel will report a confirmed alarm for the second alarm that is

triggered from a different zone within the confirmation time. There are no alarm restrictions

during entry delay or for the delay zone.

03:END EXIT MODE

Define how the exit delay is terminated or restarted according to the following options:

door/fob only (default) - When the door is closed, or by pressing the AUX button on the

keyfob

, whichever first.

restart>reentry - Exit delay restarts when the door is reopened during exit delay. The restart

occurs once only. Restarting the exit delay is helpful if the user re-enters immediately after

going out to retrieve an item that was left behind.

door/fob/timer - When the door is closed, by pressing the AUX button on the keyfob

, or when

the exit delay has expired, whichever first.

fob/timer - By pressing the AUX button on the keyfob

, or when the exit delay has expired,

whichever first.

04:FOB/KP PANIC

Define the devices that cannot trigger a panic alarm.

BS8243 (default) – MCT-234 and MCT-237.

DD243 – MCT-234.

all - All devices can trigger a panic alarm

05:CONFIRM ALARM

Define a specific time period that if 2 successive alarms occur, the second alarm will be

considered as a confirmed alarm, (see REPORT CNFRM ALARM below).

Options: 30 (default)/45/60/90 minutes

06:CONFIRM PANIC

A confirmed panic alarm is reported if one of the following occurs within the confirmation time:

a) A second panic device is activated.

b) A second panic alarm on the same device is activated.

c) A tamper event is activated (not from the zone / device that initiated the panic alarm).

Options: 4/8/12/20 (default)/24 hours and disabled

Applies only when the keyfob is defined as "skip exit delay" (for further details, see the keyfob's User's Guide)

1 2 ... 67 68 69 70 71 72 73 74 75 76

Komentarze do niniejszej Instrukcji

Brak uwag

Visonic POWERMASTER-10 Podręcznik Użytkownika Strona 72

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Visonic POWERMASTER-10